We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it. More information about our cookies and our privacy policy can be found here. OK
My Cart  

FAQ

ORTLIEB products which are returned to our customer service for a repair job or a quality check-up must be clean in order for us to guarantee an optimal repair job. For dirty products we will charge a service fee of € 5.

Advice: Modifications regarding upgrades of mounting systems may result in greases on the bag’s back.

General questions topic repair

Velcro cannot be welded on again. Please return the panniers to us via your dealer; we will exchange the Velcro with the current strap and buckle system. Please contact our customer service for more details.

We can repair holes and tears. Please give us a detailed description and/or mark the defect for us. We fix holes and tear so that your bag is waterproof. Please contact our customer service for more details.

We recommend e.g. the repair set Tip-Top Camplast, a bicycle repair set for fixing small holes and tears in bags made of PVC or PU during a trip. Further suitable repair for travelling are: Tenacious Sealing & Repair Tape by McNett, and Tenacious Tape Max by McNett. However, for a reliable long-term repair we recommend sending in your defective product to our customer service.

Depending on the material this can be normal with some products. You may cut off the fringes with a pair of scissors.

Questions topic waterproof

DIP specifications are based on standard tests defining the dustproof and waterproof levels. Further information on the different standards can be found here.

ORTLIEB products are not impregnated. A permanent waterproof lamination of the material ensures that your bag is waterproof.

Questions topic waterproof zippers and sealing lip closures

The Trunk-Bags’s zip (teeth visible) is made from extremely high-strength fabric coated with thermoplastic polyurethane. The extra strong plastic teeth are fixed on the top and bottom of the zipper tape. The zipper’s coupling elements keep the sealing edges tightly sealed together when the zipper is closed. This zipper may be lubricated from time to time at its docking end for easier opening and closing. The Big-Zip’s zip (no teeth visible when closed) is made from an extremely strong plastic coil zipper on a high strength fabric. Each coil half is safely embedded and secured in a plastic profile. When the zip is closed, the sealing lips above and below the coil are compressed making a perfect seal. For easy operation this zip must be lubricated from time to time from docking end along the entire length. Therefore, a lubricant on silicon basis and instructions for care are included.

Due to technical reasons we cannot lubricate zippers during our production. Some products include a lubricant ideal for TIZIP products. After applying this lubricant the TIZIP is easy to move without sacrificing waterproofness (note instructions of care). This lubricant is also available as accessory in specialized retails stores (art. Code E134).

The lubricant is available with your ORTLIEB dealer, it has the article code E134. It is a silicone grease for lubricating TIZIP zippers, making them open and close easier. The Cor13 is equipped with a zipper version that requires lubrication at the docking end only (also called “harbor”), not the zipper teeth themselves, therefore lubrication is not included and is required only from time to time. You may also use Vaseline or lip balm. Please remove excessive grease in order to avoid stains on clothing, gear etc.

Products with sealing lip (Quick-Seal-Closure) will be easier to operate if the closure is lubricated from time to time with silicone grease (see instructions for care). Please remove excessive grease in order to avoid stains on clothing, gear etc.

Questions topic bicycle panniers

Rear and front panniers with QL mounting system

Maximum admissible load per bag i.e. per side of the rack is 9 kg/ 19.8 lbs. However, the admissible load of the rack is to be noted. This information is normally indicated directly on the rack. The admissible load of rack may differs. The limit must not be exceeded. We recommend checking the weight of packed panniers prior to cycling by means of scales, and if necessary, to reduce the load. This applies both to rear racks and front rack or lowriders that are mounted to the front fork of the bicycle. Please note that the use of panniers may influence the riding properties of the bicycle.

Unfortunately, no. The anti-theft device can only be used in panniers with QL2 or QL2.1 system.

Yes, this is possible. Panniers with QL1, QL2 and QL2.1 system can be mounted directly into the QL3/QL3.1 rails.

The gradual change of our products to optimized buckles may result in different versions on your Back-Rollers and Rack-Pack. In this case you will need an adapter buckle in order connect your Back-Rollers with your Rack-Pack, i.e. connect the old buckle with the new buckle or vice versa (article code E135 and E186).

Due to design features the buckles must be safely inserted and fixed inside the edge protector, therefore, removing them /pulling them out requires a lot of power.

UThe hook’s position can be changed by opening it up by means of a coin.

This can be solved by mounting additional plastic blocks which are available free of charge from our customer service.

We offer a broader mounting bar (width 185 mm/ 7.2 in.) for particularly wide racks (article code E199).

No, mounting is only possible on parallel racks with a width between 60-160mm / 2.4-6.29 in.

We offer a QL2.1 hook with 20mm (article code E193) and a 16mm hook (article code E110).

Yes, you can. However, the different spacings of screws result in different holes that need to be closed by means of welding after demounting the old hooks and prior to boring holes for the QL1/QL2 system. This upgrade requires that you return your bags to our customer service. Contact them for more details please.

No, due to technical reasons this is impossible.

No, this is not possible. However, QL2.1 hooks (article code E192, E193 ) can be used on the QL2 rail without exchanging the rail.

Question topic other bicycle bag

No, the Seatpost-Bag may not be mounted to seatposts made of carbon; the seatpost may be damaged.

Handlebar bags

No, the mounting may damage the handlebar. We do not recommend handlebar bags on carbon bars for safety reasons.

See here the handlebar chart.

Ortlieb handlebar bags are designed such that the mounting is compatible with a number of different stems, handlebars and combinations thereof; a single cable version can be used for attaching Ortlieb handlebar bags to varying diameters and shapes of bars or stems. Clamp screws and cable are designed such that the cable can be fixed at any desired position ensuring that the handle bar bag remains securely mounted also in extreme conditions. In case your handle bar bag mounting had to be taken off, it is necessary to install a new mounting cable (available as accessory). Similar as with self-securing nuts, the previous mounting cable must not be used again, as the individual braids of the wire cable were squeezed by the clamp screws and the cable might have been damaged.

Yes, you can. However, the stem cannot be adjusted any more after mounting the handlebar. Mounting is only possible if you do not want to adjust your handlebar.

We offer an adapter for mounting our Ultimate6 mounting set (article code F1451).

You may use the broader Klickfix mounting for E-bikes by Rixen & Kaul instead of the Ultimate mounting. ORTLIEB handlebar bags and baskets are compatible with Rixen & Kaul. ORTLIEB offers such a mounting (article code E207).

Questions topic water transport

No, the waterbags are only suitable for transporting and storing water.

No, the water temperature must not exceed 60°C/140°F. Caution: risk of burns!

Caution: risk of burns! The material withstands high temperatures. For washing up the temperature should not exceed 45°C/113°F.

For cleaning we recommend standard artificial dentures or water disinfection tablets available in outdoor shops.

Questions topic product care

All ORTLIEB products may be cleaned with warm water and mild soap. Please do not use solvents, alcohol or acid cleaners. You may also use gall soap and a soft brush to clean your Ortlieb product.

Yes, you may.

Yes, this is a repair buckle with an opening mechanism.

* Incl. VAT

** Die Abwicklung deines Auftrags erfolgt über unseren Kooperationspartner e-shop-direct.com by arendicom. Mehr erfährst du hier: Bestellen bei ORTLIEB.